WSTW Mold Heater Injection Mold Temperature Controller

  1. Home
  2. >

Products

WSTW Mold Heater Injection Mold Temperature Controller

Details

Equipped with a microprocessor, liquid-crystal display (LCD), and controlled buttons.

The control panel is user-friendly.

Easy to operate.

Adopted the PID control to ensure the mold temperature remains lower than ±5°C.

The electronics and heating system are separated to protect the machine from overheating.

Equipped with high-quality and efficient pumps to comply with different molding temperatures.

The interior is made of stainless-steel to prevent corrosion and explosion while maintaining a constant temperature with high thermal efficiency.

The machine is protected from overloading, phase losing, overheating, and water shortage with a thermocouple alarm system.

 Model Medium Max.Temp. Pump Power(kW) Max.Flow Rate (L/min) Pump Lif(m) Tank Capacity(L) Heating Power(kW) Inlet/Outlet Diameter(inch) Dimension(cm) Net Weight(kg)
WSTW-06W Water 95°C 0.37 48 30 6 12mm×3 88×31×74 60
WSTW-09W 0.75 60 45 9 12mm×3 88×31×74 60
WSTW-12W 1.5 110 45 12 12mm×4 88×31×74 60
WSTW-24W 2.2 340 26 24 12mm×4 110×44×109 120
WSTW-36W 3.75 410 35 36 1.5″ 110x44x109 30
WSTW-60W 3.75 470 35 60 1.5″ 110×44×109 135
WSTW-06W-D 0.37×2 48×2 30 6×2 12mm×6 88×62×74 98
WSTO-06W-D Heat Transfer Oil 200°C 0.37×2 48×2 30 10×2 6×2 12mm×6 88×62×74 102
WSTO-06W 0.37 48 45 10 6 3/8″×3 88×31×74 62
WSTO-09W 0.75 60 45 10 9 3/8″×3 88×31×74 65
WSTO-12W 1.5 110 30 10 12 3/8″×4 88×31×74 75
WSTO-24W 2.2 340 35 10 24 3/8″×4 110×44×109 120
WSTO-36W 3.75 470 35 10 36 1.5″ 110×44×109 130
WSTO-60W 3.75 470 35 10 54 1.5″ 110×44×109 135

 

Model Max.Temp. Heating Power Pump Power Max.Flow Rate Pump Lift Inlet/Outlet Diameter Dimension(cm)
(kW) (kW) (L/min) (m) (inch)
VTW-06W 120°C 6  0.37 48 30 3/8″×3 88×31×74
VTW-09W 9  0.75 60 45 3/8″×3 88×31×74
VTW-12W 12  1.5 110 45 3/8″×4 88×31×74
VTW-06W-H 160°C 6 0.55 30 45 3/8″×3 88×31×74
VTW-09W-H 9 0.75 45 60 3/8″×3 88×31×74
VTW-12W-H 12 1.5 90 55 3/8″×4 88×31×74

Note: For stability, the pressure of cooling water should be between 2 and 5kg/ cm² .

Power supply: 3Φ 380VAC 50Hz

We reserve the right to change specifications without prior notice.